Plumbing 101: A Guide to Installing a Bathtub
Plumbing 101: A Guide to Installing a Bathtub
Blog Article
How do you feel in relation to Tools You Need to Install a New Bathtub ?

Installing a bath tub isn't precisely rocket science, yet it does require solid plumbing, woodworking, as well as often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately hard project. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open up a wall to remove the old tub and also place the new tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old bathtub as well as embeded in the new one. See to it you have actually certified on your own for the work and also are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to consider using one prior to you start. Opportunities are you might require a specialist plumber to make tube connections.
This short article will certainly assist you mount a brand-new bathtub in your shower room if you have already gotten a new tub as well as do not require to change the plan of your previous water supply pipes.
Your tools and material list must comprise the following:
Getting ready for the Installment
First of all, the sustaining framework provided with the bath must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap adapters to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather problematic due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, position the bath tub in the called for position. The wood boards are useful in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bath tub until the level reviews level.
To install faucets, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the supply of water as well as inspect all joints and also new pipework for leakages and tighten them if needed. Fill up the tub and likewise check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub should wait till the bathtub has actually been used at least once as this will settle it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washing machines remain in place between the faucet and the sink. Protect the faucet in place with the manufacturer offered backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The previous kind must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, resulting in complications with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and fittings. They are marketed in tubes and also cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealant can split rather early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the market. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a remark directly below. We'd be glad to see your insights about this write-up. We hope that you come back again before long. Please set aside a second to share this blog posting if you enjoyed reading it. Thank you for your time. Visit again soon.
Click Here To Find Out More Report this page